Fehler: Ein erforderlicher CD/DVD-Gerätetreiber fehlt — beim Starten von Windows 7 oder Windows Vista vom Installationsdatenträger
Windows Vista Ultimate Windows Vista Home Premium Windows Vista Home Basic Windows Vista Enterprise Windows Vista Business Windows Vista Ultimate 64-bit Edition Windows Vista Home Premium 64-bit Edition Windows Vista Home Basic 64-bit Edition Windows Vista Enterprise 64-bit Edition Windows Vista Business 64-bit Edition Windows 7 Enterprise Windows 7 Home Basic Windows 7 Home Premium Windows 7 Professional Windows 7 Starter Windows 7 Ultimate Mehr…Weniger
Zusammenfassung
Beim Starten des PCs von der Installationsdiskette für Windows 7 oder Windows Vista erhalten Sie folgende Fehlermeldung:
Ein erforderlicher CD/DVD-Gerätetreiber fehlt. Wenn Sie einen Treiber auf Diskette, CD, DVD oder USB-flash-Laufwerk haben, legen sie den Datenträger jetzt ein
Dieser Fehler kann auftreten, wenn eine oder mehrere der folgenden Szenarien zutrifft:
-
CD/DVD-Medien möglicherweise beschädigt oder verschmutzt
-
CD/DVD-Laufwerk möglicherweise nicht kompatibel mit Microsoft AHCI-Treiber (msahci.sys)
Hinweis: Wenn Ihre CD oder anderen Laufwerk im Windows Explorer-Ansicht nicht angezeigt wird, finden Sie im folgenden Artikel:
Das Laufwerk wird in Windows Explorer-Ansicht nicht angezeigt.
Problemlösung
Um dieses Problem zu beheben, lesen Sie das Szenario, das Ihre Situation am besten beschreibt:
T Das Laufwerk ist möglicherweise nicht kompatibel mit Windows 7 oder Windows Vista
Wenn Ihre Installation von Windows auf einem älteren PC CD-/DVD-Laufwerk möglicherweise nicht kompatibel mit Windows 7 und Windows Vista, müssen das Laufwerk ersetzt werden.
CD/DVD-Medien möglicherweise beschädigt oder verschmutzt
Entfernen Sie die DVD-Medien und Kontrollkästchen Kratzer, Risse oder Flecken, die erschweren können die DVD lesen, wenn Kratzer oder Risse Medien Ersatzmedien erhalten müssen. Wenn die DVD verschmutzt oder verschmiert ist, reinigen Sie DVD mit warmem Wasser und einem weichen Tuch Stellen Sie sicher, dass die DVD vollständig sauber und trocken ist, bevor Sie sie erneut in das Laufwerk einlegen. Anschließend starten Sie den Computer neu, und drücken Sie eine Taste, wenn Sie dazu aufgefordert werden, und starten Sie Setup.
Das Laufwerk ist möglicherweise nicht kompatibel mit Microsoft AHCI-Treiber (msahci.sys)
Wenn Ihr Laufwerk nicht kompatibel mit Microsoft AHCI-Treiber (msahci.sys) ist, kann der Festplattencontroller AHCI im BIOS fest. Sie können das Problem eventuell beheben, indem Sie den AHCI Modus ihres Platten-Controlers im BIOS deaktivieren. Mehrere BIOS-Hersteller und BIOS-Versionen, finden Sie in oder auf der Website der PC-Hersteller Anleitung zum Ändern dieser Einstellung werden soll.
Hinweis: das grundlegende Verfahren zum Ändern der Einstellung der Festplatten-Controller ist, den Computer neu starten und das System-BIOS. Die gängigste Methode, drücken F2, um Setup ist (anderen PC kann einen anderen Schlüssel verwenden). Der BIOS-Bildschirm wechseln Sie auf die Einstellung, die AHCI, ATA oder IDE und RAID bietet. Wenn die auf AHCI eingestellt ist, ändern Sie die Einstellung auf ATA. Starten Sie den PC, die Windows Setup-Diskette
Warnung: Falsche Einstellung im BIOS können Ihren PC Fuktionsunfähig machen. Wenn Sie konfigurieren das System-BIOS nicht kennen, wenden Sie PC-Hersteller um Unterstützung zu erhalten.
Wenn Sie sind können nicht noch PC aus dem Windows 7 oder Windows Vista finden Sie unter Weitere Optionen starten für Windows installieren unten:
-
Ersetzen Sie das Laufwerk
-
Installieren von Windows mithilfe von Windows Setup von einem USB-Laufwerk
-
Installieren Sie Windows mithilfe einer Netzwerkinstallation oder online-installation
-
Hersteller der Hardware für Support kontaktieren
WIndows 7 lässt sich wegen fehlender Treiber nicht installieren. | Die Hardware-Community für PC-Spieler
Lycon_
Schraubenverwechsler(in)
-
-
-
#1
WIndows 7 lässt sich wegen fehlender Treiber nicht installieren.
Hallo zusammen,
ich hab mir gerade einen neuen PC zusammengebaut und wollte ihn nun starten und Windows 7 64Bit darauf installieren.
Die istallation von dem USB-Stick per Windows 7 iso. hat bei mir normalerweise sonst immer funktioniert. Jetzt mit der neuen Hardwear kommt allerdings die Fehlermeldung. «Ein erfoderlicher CD/DVD-Treiber fehlt…» und es geht nicht weiter. Hab aber von dem USB-Stick gebootet. Hab auch schon alle USB-Ports durchprobiert (2.0-3.0) jetzt weiss ich aber nicht mehr weiter… Habt ihr eine Idee? Wäre froh wenn mir jemand weiter helfen könnte
Danke schonmal im voraus
Mfg Adrian
Tolotos66
Volt-Modder(in)
-
-
-
-
#2
AW: WIndows 7 lässt sich wegen fehlender Treiber nicht installieren. Hilfe!
Welche Plattform? Du brauchst wahrscheinlich Dies hier: Skylake unter Windows 7 installieren | 3DCenter.org
Gruß T.
Lycon_
Schraubenverwechsler(in)
-
-
-
-
#3
AW: WIndows 7 lässt sich wegen fehlender Treiber nicht installieren. Hilfe!
Hab einen Kaby Lake, aber auch ein neues z270 MB… dachte das würde den CPU unterstützen….
drstoecker
Lötkolbengott/-göttin
-
-
-
-
#4
AW: WIndows 7 lässt sich wegen fehlender Treiber nicht installieren. Hilfe!
Haste schon mit ner dvd versucht?
Darkscream
Freizeitschrauber(in)
-
-
-
-
#5
AW: WIndows 7 lässt sich wegen fehlender Treiber nicht installieren. Hilfe!
Die CD welche beim Board dabei war ins Laufwerk (wenn du eines hast) und dann gehts auch weiter. Da ist der fehlende Treiber drauf.
Lycon_
Schraubenverwechsler(in)
-
-
-
-
#6
AW: WIndows 7 lässt sich wegen fehlender Treiber nicht installieren. Hilfe!
nein hab ich nicht, ich hab noch so ein uralt Laufwerk welches ich garnicht an mein Mainboard anschließen kann…
Lycon_
Schraubenverwechsler(in)
-
-
-
-
#7
AW: WIndows 7 lässt sich wegen fehlender Treiber nicht installieren. Hilfe!
oh das heisst ich muss mir ein neues Laufwerk kaufen…? kann man das nicht auch irgendwie über USB zum laufen bringen ?
Darkscream
Freizeitschrauber(in)
-
-
-
-
#8
AW: WIndows 7 lässt sich wegen fehlender Treiber nicht installieren. Hilfe!
Du musst dir deinen Stick mit cb. dem Tool erstellen: ASRock-Installing Windows 7 on Intel Braswell and Skylake Platforms — da wird der Treiber intergriert.
Lycon_
Schraubenverwechsler(in)
-
-
-
-
#9
AW: WIndows 7 lässt sich wegen fehlender Treiber nicht installieren. Hilfe!
ok das hört sich schonmal gut an. Werde ich versuchen. Danke
Lycon_
Schraubenverwechsler(in)
-
-
-
-
#10
AW: WIndows 7 lässt sich wegen fehlender Treiber nicht installieren. Hilfe!
ich hätte da noch eine Frage, sorry falls die dumm scheint aber welche serie ist ein Kaby Lake, 100 Series oder N3000/J3000? Und ich hab ein MSI Mainboard, da würd ja das mit dem ASRock Treiber eher nicht gehen oder?
Danke. Ich bin noch recht unerfahren was PC-bauen angeht.
Esinger
Guest
-
-
-
-
#11
AW: WIndows 7 lässt sich wegen fehlender Treiber nicht installieren. Hilfe!
nimm einfach win10 und gut ist es
immer dieses drecks win7 leute haben wollen echt zum kotzen
Lycon_
Schraubenverwechsler(in)
-
-
-
-
#12
AW: WIndows 7 lässt sich wegen fehlender Treiber nicht installieren. Hilfe!
hm das Problem besteht leider weiterhin. Hab jetzt zwischenzeitlich mal die ganzen Treiber mit dem Laptop runtergeladen, auf einen USB-Stick gepackt und versucht diese von dem Stick aus auf den neuen PC zu installieren. Hat nicht geklappt. Das Problem ist das er den Stick bei der Durchsuchung nicht zeigt. Im Bootmenü steht er mir aber zur Auswahl. Kann nur nicht vom Windowsinstallationsvorgang den Stick finden. Komisch. Hat jemand noch eine Idee?
Lycon_
Schraubenverwechsler(in)
-
-
-
-
#13
AW: WIndows 7 lässt sich wegen fehlender Treiber nicht installieren. Hilfe!
@Eisinger. Gut ich probiere es aus. Hatte halt eben nur Windows 7 da. kein Grund unfreundlich zu werden. Werde es mir besorgen.
Jeretxxo
BIOS-Overclocker(in)
-
-
-
-
#14
AW: WIndows 7 lässt sich wegen fehlender Treiber nicht installieren. Hilfe!
Das reicht auch nicht die Treiber auf den USB Stick zu packen, die müssen in die Intsallationsroutine eingebunden werden.
Hier geht es zwar grundsätzlich um Ryzen in dem Artikel, aber das Problem und die Lösung sind die gleichen.
Ryzen (AM4): Anleitung zur Installation von Windows 7 — ComputerBase
Eventuell hast du aber auch die Einstellung im BIOS namens «xHCI oder EHCI handoff» damit sollte sich Windows 7 auch an dem USB Anschluss normal installieren lassen.
Normalerweise haben alle Z170 und Z270 Mainboards diese Einstellung, im Gegensatz zu den Mainboards für Ryzen.
T-Drive
Guest
-
-
-
-
#15
AW: WIndows 7 lässt sich wegen fehlender Treiber nicht installieren. Hilfe!
Lycon_ schrieb:
@Eisinger. Gut ich probiere es aus. Hatte halt eben nur Windows 7 da. kein Grund unfreundlich zu werden. Werde es mir besorgen.
Zum Vergrößern anklicken….
Mach das lieber nicht, da kommen dann halt andere Probs nach der erfolgreichen installation.
Lycon_
Schraubenverwechsler(in)
-
-
-
-
#16
AW: WIndows 7 lässt sich wegen fehlender Treiber nicht installieren. Hilfe!
zu spät habs mir eben besorgt installation läuft gerade. Bis jetzt bin ich aber schonmal weiter wie davor und das ist für mich schon mal positiv Falls es mir nicht zusagt kann ich mich ja dann noch in ruhe um eine Lösung kümmern, um Win 7 erfolgreich zu installieren Hauptsache der Rechner läuft und ich muss mich nicht mit dem alten Laptop hier rumschlagen. An dieser Stelle nochmal Danke! für alle Tips und Vorschläge!
Gruß Lycon_
Bioschnitzel
PCGH-Community-Veteran(in)
-
-
-
-
#17
AW: WIndows 7 lässt sich wegen fehlender Treiber nicht installieren.
Ist schon richtig so, auf ein mittlerweile 8 Jahre altes OS zu setzen ist absolut nicht sinnvoll.
Ich habe Windows 10 seit Release drauf, bisher gar keine Probleme.
T-Drive
Guest
-
-
-
-
#18
AW: WIndows 7 lässt sich wegen fehlender Treiber nicht installieren.
Wer mit «friss oder stirb» glücklich ist, bitte sehr.
Manche lieben halt Zwangsupdates.
wenns schee macht . ..
Bioschnitzel
PCGH-Community-Veteran(in)
-
-
-
#19
AW: WIndows 7 lässt sich wegen fehlender Treiber nicht installieren.
Zwangsupdates haben einen großen Vorteil, man ist immer aktuell.
Das was viele Nutzer eben nicht hinbekommen
Wobei man simple per Registry-Eintrag auch sein Windows 10 auf manuelle Updates umstellen kann.
Aber hey, Windows 10 ist «neu», ist ja nicht so als ob bei jeder neuen Windows Version erstmal gemeckert werden muss
How to install Windows 7 from a flash drive with the error «The required driver for the optical drive was not found» .
Owners of modern laptops and home computers based on chipsets released in 2016-2017. faced with
that on this equipment, an attempt to install Windows 7 is accompanied by the following message:
The required driver for the optical drive was not found. If you have a floppy disk, CD, DVD, or USB flash drive with this driver, insert this media
Or for Windows 7 English:
A required CD/DVD drive device driver is missing. If you have a driver floppy disk, CD, DVD, or USB flash drive, please insert now.
After that, further installation of Windows 7 stops.
Sometimes a similar error occurs on relatively old hardware when installing Windows 7 from a flash drive connected to a USB 3.0 port on motherboards,
where there are standard USB 2.0 ports. In such a case, it is enough to connect the USB flash drive to the USB 2.0 port and the system installation will run normally.
The main problem that causes the installation error is the lack of support for USB 3. 0 by the Windows 7 installation software. Accordingly, the solution to the problem is to provide this support.
Installation of all modern operating systems of the Windows family is performed using two images of the Windows Imaging (WIM) format, namely —
files boot.wim and install.wim . Image boot.wim contains a bootable version of Windows PE (Windows Preinstall Environment),
from which the system itself is installed using the contents of the image file named install.wim . In cases where the preset environment
is deployed on unsupported hardware, it fails to get a set of critical devices for further operation,
such as a hard drive or installation flash drive (on an unsupported USB 3.0 port) and, of course, further Windows installation stops.
When installing from a flash drive, the message «The required driver for the optical drive was not found» means that the preinstallation environment cannot access
main installation file install. wim , located on a flash drive that requires a USB 3.0 driver to access, not an “optical disc drive”.
Usually, as a solution to this problem, the installation images of boot.wim and install.wim include the missing drivers using special software. However, there is an easier way, based on using a ready-made boot.wim image from Windows 8/8.1 to install Windows 7. In other words, the easiest way is to take a bootable USB flash drive for installing Windows 8/8.1 and replace the install. wim file from the Windows 7 distribution. Thus, the preinstallation environment will be created based on the image from Windows 8, which supports USB 3.0 and other newer computer equipment, and the system will be installed from the install.wim image taken from the Windows 7 distribution. The advantage of this technique is simplicity, and the disadvantage is the lack of USB 3.0 support in a newly installed system. After such an installation of Windows 7, first of all, you will need to solve this, not very complicated, problem. Here I’ll show you the simplest method of installing Windows 7 using a Windows 8 /8.1 bootable flash drive with the install.wim image file replaced.
Creating a bootable flash drive with Windows 8
Today, there are dozens of programs and ways to create bootable flash drives for installing Windows — from using standard command line tools to using specialized third-party programs. For example, I took probably the most method using the free Rufus program. To work, you will need the program itself, an iso image of Windows 8, and the actual flash drive, which will become a hybrid of Windows 8 and Windows 7 distributions. The Rufus program does not require installation on the system, just download it from the developer’s website and run it. The program interface is very simple:
The procedure for creating a bootable flash drive with Windows 8 is as follows:
select the flash drive on which the image will be written. All other parameters can be left by default and simply set the path and file name with the iso image of Windows 8. Just in case, I give the optimal parameters for creating an installation flash drive with Windows 7 for computers with BIOS or UEFI» — the most common mode for bootable flash drives today.
File system FAT32 , but you can select NTFS if you want to use files larger than 4 GB.
The cluster size is selected by the program based on the image data and file system type.
You can specify the volume label that will be set for the created flash drive.
Leave the formatting options as default and just select the ISO image file with the Windows 8 distribution.
After pressing the Start button , the program will format the flash drive, set the active partition flag, write the master boot record and partition boot record, as well as bootable media data from the ISO image. After the completion of Rufus , we will receive a bootable USB flash drive with Windows 8.
Changing the bootable Windows 8 flash drive to install Windows 7
The Windows 8 installation flash drive obtained in the previous step has the usual content for Windows 7 or Windows 8:
Preinstallation environment images boot.wim and windows 8 installation install.wim are located in the Sources folder :
You need to leave the image file boot.wim unchanged and replace the file install.wim with a file with the same name from the Windows 7 distribution. For example, copy it from a DVD, extract
from an ISO image using the 7-zip archiver or copy from a virtual drive based on an iso image created by Daemon Tools, Alcohol 120%, Nero, etc. After that, you can boot from the received flash drive and install Windows 7 using the Windows 8 Preinstallation Environment.
After the installation of Windows 7 is complete, if the network adapter is recognized by the system, device drivers can be installed over the network, but most likely this will not happen. Still, it is more likely that some part of the drivers will need to be installed from a flash drive that cannot be recognized by the newly installed Windows 7. To solve this problem, you need: USB from motherboard manufacturer.
— Boot into Windows 8 PE and copy the drivers folder to your hard drive.
— Boot from the hard drive and install the drivers using the data previously copied from the flash drive.
— Further updates and installations should be carried out as usual.
To perform these actions, it is convenient to use the MS DaRT emergency recovery boot disk (flash drive), but you can get by with the same flash drive you created earlier with the Windows 8 preinstallation environment. ”, which will load the recovery environment (Windows Recovery Environment, or Windows RE) of the Windows 8 operating system.
Action menu (for Windows 8.1 — Windows 10) allows you to:
— continue normal Windows boot ( Continue )
— proceed to boot system recovery tools ( Troubleshooting )
— turn off computer.
We naturally choose Troubleshooting .
Next — Diagnostics — Additional parameters — Command line .
After that, the command processor of the recovery environment will be launched. Using the command line, you can copy the folder with the drivers,
pre-recorded on a flash drive, for example, under the name Drivers on a hard drive. Since the letters
disks in the recovery environment, as a rule, are unknown, before copying it is worth running the utility diskpart.exe and in its prompt line for entering commands enter:
list volume — display a list of volumes.
In response, we will receive a list from which it will be possible to obtain the necessary information:
Volume ### — Volume 0 Volume 1 Volume 2 Volume 3 |
Name — F C D E |
Label —— Zarezer FD16 |
FS —— NTFS NTFS NTFS NTFS |
Type — DVD-ROM Section Section Replacement |
Size — 0 b 350 MB 461 GB 14 GB |
Comp — Rev Rev Rev Rev |
Based on the size of the partition and the type of device, you can determine which letter corresponds to the flash drive and which letter corresponds to the system drive with Windows 7 installed. In this case,
the flash drive corresponds to the letter E , and the hard drive with Windows 7 installed to the letter D . We finish working with the utility diskpart with the command:
exit
and copy the folder with the drivers:
xcopy /s E:\Drivers D:\ — copy folder Drivers with subdirectories ( parameter /s ) from disk E: to disk D:
Windows 7 and proceed to install the drivers using the contents of the Drivers directory on the system drive as a source.
Creating a bootable USB Flash with Windows 7 from Ubuntu / Sudo Null IT News0001
A friend recently asked me to install Windows 7 for him. It just so happens that my DVD drive hasn’t worked for a long time, but I have an 8 GB flash drive. The topic of creating a bootable USB flash drive with Windows 7 from under Windows has long been heavily chewed on the Web. But I use Ubuntu, so I had to look for another solution. In fact, it seems to me that it is even simpler.
To begin with, we need the graphical utility GParted and a package for working with the NTFS file system. To do this, just install the gparted and ntfsprogs packages. This can be done both through Synaptic and through the console:
sudo apt-get install gparted ntfsprogs
Next we need to format the flash drive.
You can do this from the console:
sudo mkfs.ntfs /dev/sdb4
instead of / dev / sdb4, of course, there should be the address of your flash drive
It can also be done in an easier way. To do this, launch GParted, select the flash drive (drop-down menu on top) and select the partition. Select the «Unmount» submenu in the «Partition» menu, then again in the «Partition» menu, the «Format to» submenu and select «ntfs» in the drop-down menu. Click the green checkmark on the toolbar.
If you formatted the flash drive through the console, then you still have to run GParted in order to set the boot flag on the flash drive. Select the desired section, select the «Section» menu, the «Set flags» submenu. In the window that appears, put a tick on «boot» and close the window. We don’t need GParted anymore.
The next problem I encountered was that the standard Ubuntu tools do not allow opening a UDF ISO image. Therefore, you need to mount the image manually:
sudo mkdir /media/iso
sudo mount windows7.iso /media/iso -t udf -o loop
It remains only to copy all the files from the image to the flash drive:
cp -R /media/iso/* /media/MyFlashDrive
That’s it!
P.S. In principle, you can not only copy Windows 7 to a USB flash drive in this way.
UPD. You can do without using GParted at all. You can use fdisk instead (thanks icCE)
bogus@bogus-laptop:~$ sudo fdisk /dev/sdb
Command (m for reference): p
Drive /dev/sdb: 1998 MB, 1998585344 bytes
255 heads, 63 sectors/track, 242 cylinders
Units = cylinders of 16065 * 512 = 8225280 bytes
Disk identifier: 0x00068ccc
Load Device Start End Blocks Id System
/dev/sdb4 1243 1951712 7 HPFS/NTFS
Partition 4 has different physical/logical endings:
phys=(241, 254, 63) logical=(242, 250, 7)
Command (m for reference): a
Partition number (1-4): 4
Command (m for reference): p
Drive /dev/sdb: 1998 MB, 1998585344 bytes
255 heads, 63 sectors/track, 242 cylinders
Units = cylinders of 16065 * 512 = 8225280 bytes
Disk identifier: 0x00068ccc
Load Device Start End Blocks Id System
/dev/sdb4 * 1 243 1951712 7 HPFS/NTFS
Partition 4 has different physical/logical endings:
physical=(241, 254, 63) logical=(242, 250, 7)
Command (m for reference): w
The partition table has been changed!
Called ioctl() to reread the partition table.